RoundsLogging Logo Tango Mobile Logo

RoundsLogging Manual

Important Information

RoundsLogging has been designed to work both Online and Offline. However, there are restrictions to Offline Uses.

While Online:
  • Routes can be downloaded to the Wireless Device. After a Route has been downloaded, that Route restricts any other users from accessing that route.
  • Route Points will be saved to the server once "Save" has been clicked.
  • "End Route" will save and upload the Route back to the server, allowing other users to select that Route.

While Offline:
  • Routes can not be downloaded.
  • Only one route can be opened during Offline Status.
  • User must have the Route opened before going Offline or the user will not be able to access the Route.
  • Measurements can be added, but not saved to the server.
  • Route Points will be saved to the Device's "Cache" until the Device is back Online. Once a connection is found by the Device, the "Stored Data" will be automatically uploaded.
  • User can not navigate away from the browser or all information will be lost.
    Note Users will be given two pop up warning messages that all data saved to the device will be lost before leaving the Route Measurement Entry pages.





Building a Route:

In the Tango Webservices, you can now add a route from any level of the tree.

Click the Menu Options next to the desired level.
Note By choosing a unit level, the route editor will only allow users to select points under that unit. Choosing a function level will only allow users to select points under that function. This will reduce load times and make it easier to filter out unwanted points.


Select Process Parameter Routes from the drop down menu.

RoundsLogging Route Set-Up


Click Add Route.

RoundsLogging Route Set-Up


Fill out the form and Click Save.

Locate the route from the route list and click the Edit Button Route Location Edit.

Select from Route List


The Route Editor page will be displayed where users can edit the route information or edit the location points.

Click Edit Locations to add points to the route.

Check each box of the Location which should be included on the route and fill out the order of the location.
Note When filling out the route order, input must be a numerical value. Also, users may want to use 10, 20, 30 instead of 1, 2, 3 so that future points can be added without reordering the list.


Select points for Route List


Add any special instructions that should be known, while the route inspection is in progress, in the instruction column.

Click Save.



Logging Into RoundsLogging

To log into RoundsLogging the user must contact us to be set up as a user. Once a user is set up, a URL will be given to the user. This URL will provide a Log In Screen to access the User's Routes.

1.) Enter User Name and Password (this will be the same username and password as your Tango™ Account)

2.) Touch "Login"

RoundsLogging Log In

3.) Select the Database associated with the Route

Choose Database



Route Quick Search

On the Available Routes List, a user can filter the results with the Route Quick Search. To filter the results, touch in the text box and type a keyword to search, then touch the Filter Button.
Quick Search Filter

To return to the full list, touch the Refresh Button and all available routes will refresh.



Downloading Route

Once the user has logged in and selected the database (described above), a list of available routes are will be displayed (Available Routes Page).

Available Routes

To download a route, simply touch the desired Route. The Route will open, starting with the first Route Point.

Note: Once a user has downloaded and open the Route, they must keep that Route open before going Offline to be able to enter measurements.



Entering Measurements

Once a Route has been downloaded and opened, other users will not be able to see or change Route information.

The route will begin at the first point of the route according to the route order. However, there are multiple options on the screen:
Entry Screen

  • A: Location Information - Shows the locations of the point.
  • B: Point Number and Status - Indicates what point the user is on and the current status of that point.
  • C: Data Entry Section - This section is where the data will be added or selected.
    Note Depending on the Point type, Trend, Observation, or Gauge, the user will have different input options (drop down list, text field, etc.).

  • D: Not Measured Status Button - This button allows the user to enter a reason the point can not be measured.
  • E: History Of Measurements - Shows the history of this point's measurement.
  • F: Linked Documents - Shows any linked documents that are associated with this location.
  • G: Point Navigation Buttons - Allows the user to move to the Starting Point, Previous Point, Next Point, or Last Point of the Route.
    Note Starting Point (1st button - Double Back Arrow), Previous Point (2nd button - Single Back Arrow), Next Point (3rd button - Single Forward Arrow), or Last Point (4th button - Double Forward Arrow)

  • H: Status Display - Show the status of the users mobile connection, "Online" (Uploads instantly) or "Offline" (Uploads at a later time when connected).
  • I: Route Options - Allows the user to see the Route List, see more.
  • J: Point Search - Allows users to search for barcode alias value.


Entry Screen Types

1.) There are 3 inputs types that may be available to the user:
  • A: Drop Down List - For a drop down list, touch the drop down arrow, and select the desired option and touch done.
    Entry Types Drop Down

  • B: Text Input Value - For a text field, touch inside the text box and enter the value via the device's keyboard.

  • C: Not Measured Options - If the point is not able to be assessed, users may have a not measured option.

    Touch the "Red X".

    Select the desired option from the drop down list.

    Enter any additional information.

    Not Measured Options

    Note The database must be configured to have this option, please request to your Tango™ Administrator to contact us to have this option turned on.

2.) Click "Save". After touching save, RoundsLogging either:
  • Automatically move to the next Route Point.
  • A Condition Entry Request Screen will be displayed if the measurements are outside of the set limits, after a Condition Entry Request is saved, the next Route Point will be displayed.
3.) Repeat steps 1 and 2 until all Points are measured.

4.) Users can browse through the points manually by touching the "Navigation Buttons" or "Option" button at the bottom.

5.) Once all points are correctly entered, users can review the status of each point in the Route by touching "Options" at the bottom of the screen, this will load the Route List.



Condition Entry Request

If a Route Measurement is entered and saved that is not within the set limits, a Condition Entry Screen will be displayed.

Enter a reference number and a comment into the appropriate fields and touch "Save".

Condition Entry Request

Once a Condition Entry Request is saved, the next Route Point will display. However, the "Request" is a call to action for a manager or planner to create a condition entry from the Process Parameter Collected Data section in Tango™. Move to the Completing Condition Entry Requests for Tasks section.



Route Point List and Ending a Route

The Route Point List will show the Order number, Status (measured or not measured), Route Item/Location, Bar Code (if available), and previous value information.

Points highlighted in Green are measured, yellow highlight indicates the next point requiring measurement, and no highlights still requires measurements or is not able to be measured.

Touchable Options for the Route List:
  • A: Order Number Point Selection - Touching the order number beside a Route Point will display that point and allow users to take measurements.
  • B: Checkboxes and Assignment Previous Values Option - By Checking the checkboxes, users can apply all previous values to those points.
    Note In order to assign previous values, the "Allow Previous Values" must be yes.

  • C: View Routes - This will take the user back to the Route Selection List. *
    Note Any data taken will be lost if the user navigates away from the route.

  • D: Complete Route - This will complete the route, even if not all measurements are taken. *
    Note Users will not be able to open that route again to make changes once they have closed the route. The data will not be uploaded to Tango™ until the device has an internet connection.

  • E: Cancel Route - This will cancel the route and remove any of the values that have been saved. *
    Note To be sure the route is cancelled and another user will be able to open the route, make sure the device is Online when cancelling.

  • F: Log out - Logs the user out of Roundslogging. *
* Must have an internet connection to complete this option.
Route Point List


Completing the Condition Entry Requests

For Process Parameter Task:

If a point is measured and is out of the acceptable range, once the task is complete, view the route overview by clicking "Options" and the bottom of the screen.

The route overview will show all the measurements for the route, the out of range measurements will have a red icon next to the value.
Out of Bounds


To complete the condition entry request, user will need to login to Tango™.

Collected Data


1) Click "Services"

2) Click "Process Parameters"

3) Click "Collected Data"

4) Select the "Task Name" in the drop down list on the main window, or find the task with the other search options on this screen.
Note If the task is still opened, a search will display the Task, but users will not be able to open the report until the Task has been completed.



5) Click "Search"

Collected Data Report


Click the "Report Icon" to bring up the "Process Parameter Route Info" page.

Collected Data Report


Any point that needs a condition entry will have a "Add Entry" button in the row. Click the "Add Entry" button and a Condition Entry Editor will load in the main window.

Fill out the condition entry details and click "Save".

The "Process Parameter Route Info" will be reloaded, the "Add Entry" will now be a "View" button, users can click this button to view the condition entry.

Complete any other Condition Entries to complete the Task.


For Condition Assessment Assignment Condition Entries: Click Here




Setting Up a Condition Assessment Assignment Route

To learn how to setup a Condition Assessment Assignment Route, please visit the Condition Assessment Assignment Manual.



Condition Assessment Assignment Route

Condition Assessment Assignment Routes can also be ran from Roundslogging.
Note The Condition Assessment Assignment must be set up properly before it can be ran from Roundslogging. To see how to set up an assignment for Roundslogging


Running an assignment from Roundslogging is the same as running a normal task. However, the difference is that only the states are available to assign as a measurement value.
Route Point List


If the value requires more information, (eg. "Measured, Condition Entry" or "Measured, No Problem, Add Condition Comment") the user needs to enter their comments.
Route Point List


If there are any measurements that require a condition entry or comment, the user will need to log back into Tango™ and open the "Condition Assessment Task Control Panel".

From the open assignment tab, open the assignment by clicking the Enter/Edit Assignment Data from the drop down menu next to the assignment. If all points have been measured, and the "To Do" filter is on, only the points that require further action will be present. The points that require action will have a status of "Field Info" in Red. Click the drop down menu button, and click Assess.

State Field Info


Complete the condition entry. Once all points have been assessed, a prompt to close the assignment will be displayed. Click "OK" to complete the assignment.